Call US:

UAV Pilot

Drone DIY solutions

  • Home
  • Copter
  • Plane
  • Rover
  • Sub
  • PX4
  • Mission Planenr
  • ArduPilot

Pixhawk

Pixhawk 

Pixhawk:some motor not run

February 12, 2022February 12, 2022 dronecode 0 Comments

if you meet some motor not run.Please check the Servo Output Make sure the function of Motor is Motor 1..4.

Read more
Pixhawk 

Parameter Reset

December 26, 2021December 26, 2021 dronecode 0 Comments

https://ardupilot.org/copter/docs/common-parameter-reset.html This article shows several ways to reset all parameters to their default values.If you would like to restore any

Read more
Pixhawk 

Barometer (external)

October 24, 2021October 24, 2021 dronecode 0 Comments

Link from https://ardupilot.org/copter/docs/common-baro-external.html Most autopilots include a barometer directly on the autopilot but attaching an external barometer can be useful

Read more
Pixhawk 

Ardupilot How to Connect ESCs and Motors

August 18, 2021August 18, 2021 dronecode 0 Comments

This article explains how to connect the ESCs, motors and propellers to a autopilot. The Pixhawk is used as an

Read more
Pixhawk 

PX4 avionic power low :4.30V

July 27, 2020July 27, 2020 dronecode 0 Comments

Some people may meet this problem,If this error causes the pixhawk to fail to arm, it is because the voltage

Read more
Pixhawk 

Pre-Arm Safety Checks

April 12, 2020April 12, 2020 dronecode 0 Comments

ArduPilot includes a suite of Pre-arm Safety Checks which will prevent the vehicle from arming its propulsion system if any

Read more
Pixhawk 

How to solve Check Board Voltage

April 8, 2020April 8, 2020 dronecode 0 Comments

1.For 3.4.6 version firmware Do not select Board Voltage at Arm_check parameter,then remember to click the “Write Params”Button. Then reboot

Read more
Pixhawk 

Prearm Board 4.2V out of range 4.3-5.8V

April 5, 2020April 5, 2020 dronecode 0 Comments

If you use ardupilot firmware 4.0 or higher, you may encounter this problem. This is due to insufficient external power

Read more
Pixhawk 

HOW to use airspeed sensor

September 23, 2019September 23, 2019 dronecode 0 Comments

Upload Plane firmware, airspeed only can be supported for Plane firmware, do not use for Copter or other. 2.Connect Dynamic

Read more
Pixhawk 

HOW to use OLED for PIXHAWK

August 26, 2019August 26, 2019 dronecode 0 Comments

Use OLED for PIXHAWK, must follow these steps, Connect OLED to I2C port of Pixhawk Upload ardupilot firmware, at least

Read more

Recent Posts

  • HOW to use wifi V2.0 for APM?
  • How to use wifi V2.0 for pixhawk?
  • How to use WIFI V3.0?
  • How to use WIFI 2.0?
  • Pixhawk:some motor not run

Recent Comments

  • Fashion Styles on How to solve “Failed to discover board id”
  • Fashion Styles on APM2.8 with internal compass
  • 500MW:How to use Radio Telemetry? – UAV Pilot on How to use Radio Telemetry For APM flight controller?

Archives

  • April 2022
  • February 2022
  • December 2021
  • November 2021
  • October 2021
  • August 2021
  • July 2021
  • June 2021
  • March 2021
  • December 2020
  • October 2020
  • August 2020
  • July 2020
  • June 2020
  • May 2020
  • April 2020
  • February 2020
  • November 2019
  • October 2019
  • September 2019
  • August 2019

Categories

  • 3DR Power Module
  • APM
  • CC3D
  • F3
  • F4
  • GPS
  • miniOSD
  • mission planner
  • Pixhawk
  • Pixracer
  • PX4
  • Radio Telemetry
  • RC
  • Video Transmitter
  • VTOL

Meta

  • Register
  • Log in
  • Entries RSS
  • Comments RSS
  • WordPress.org
Copyright © 2022 UAV Pilot. All rights reserved.
Theme: ColorMag by ThemeGrill. Powered by WordPress.